Preview

Russian Journal of Industrial Economics

Advanced search

Implementation of the new resource saving technology in manufacturing process

https://doi.org/10.17073/2072-1634-2020-4-494-502

Abstract

The authors of the article justify the expediency of applying resource saving in developing innovative technologies for hot rolling of boning knife blades from steel slabs. Such knives are widely used in meat processing industry. Metal consumption of the process was significantly reduced after changing the existing factory technology of making boning knives. The operation of cutting or grinding was replaced by hot rolling. The specific feature of the technology lies in minimizing the metal loss into shavings during the final processing of the steel slab by means of cutting. Reducing metal loss in making such steel parts and raising metal utilization rate are achieved by maximum possible approximation of forging configuration to the end product contour and preservation of the allowances regulated by the operational chart. The authors suggest optimal combinations of basic parameters of introduction of resource saving technology into production. To adduce an example the authors justify the possibility of shaping and simultaneous hardening of the knife blade during hot rolling between deforming rollers. Energy intensity of the technology suggested is lowered by means of reducing the time for further mechanic processing of the forging by cutting. Practical approbation of the introduced resource saving technology in repair production made it possible to raise the metal utilization rate to 95% and to reduce by 1.2 the production cost of a boning knife as the end product. When manufacturing the parts metal resources are saved due to the fact that irreversible loss of metal in the innovative technology of the boning knives’ production differs a lot from that in the traditional one. Technical and economic calculations adduced in the article show the effectiveness of the research and prove the profit of implementation of the new technology

About the Authors

K. P. Kolotyrin
Saratov State Vavilov Agricultural University
Russian Federation

Konstantin P. Kolotyrin – Dr.Sc. (Econ.), Professor of Department of Project Management and Foreign Economic Activity in Agricultural Complex

1 Teatralnaya Ploshchad, Saratov 410012



S. A. Bogatyryov
Saratov State Vavilov Agricultural University
Russian Federation

Sergey A. Bogatyryov – Dr.Sc. (Eng.), Professor of Department of Project Management and Foreign Economic Activity in Agricultural Complex

1 Teatralnaya Ploshchad, Saratov 410012



F. Ya. Rudik
Saratov State Vavilov Agricultural University
Russian Federation

Felix Ya. Rudik – Dr.Sc. (Eng.), Professor of Department of Project Management and Foreign Economic Activity in Agricultural Complex

1 Teatralnaya Ploshchad, Saratov 410012



References

1. Panov A.A., Anikin V.V., Boym N.G. et al. Metal cutting: A Technologist Handbook. Moscow: Mashinostroenie 2004. 784 p. (In Russ.)

2. Patent 2087238 (RF). Method of manufacturing cutting tools. P.A. Andreev, S.A. Bogatyrev, E.F. Koleturin, V.D. Kostin, G.I.Mednikov, F.Ya. Rudik, A.G. Rybalko. Stated 18.12.1995; published 20.07.1997. Bulletin No. 23. 6 p. Available at: https://yandex.ru/ patents/doc/RU2087238C1_19970820 (In Russ.)

3. Aleinikov A.K., Scriabina L.Yu., Fomin R.B. Analysis of technologies for the production of boning knives. Materials of the II International Scientific and Technical Conference dedicated to the 100th anniversary of the honored worker of science and technology, professor V.I. Popov «Progressive technologies and equipment for the food industry». Voronezh, 2004. Pp. 60–61. (In Russ.)

4. Design, construction and calculation of food technology technology. Ed. V.A. Panfilov. St. Petersburg; Krasnodar: Lan, 2013. 912 p. (In Russ.)

5. Patent 2098214 (RF). Method of manufacturing semi-finished blades of knifes. P.A. Andreev, S.A. Bogatyrev, A.M. Vlasov, E.F. Koleturin, V.D. Kostin, G.I. Mednikov, F.Ya. Rudik. Stated 04.03.1996; published 12.10.1997. 7 p. Available at: https://yandex.ru/ patents/doc/RU2098214C1_19971210 (In Russ.)

6. Patent 150113 (RF). Device for the manufacture of cutting tools. F.Ya. Rudik, S.A. Bogatyrev, A.P. Kovylin, A.V. Popova, A.A. Morozov. Stated 24.04.2014; published 27.01.2015. Bulletin No. 3. 8 p. Available at: https://patentinform.ru/utility-models/reg150113.html (In Russ.)

7. Kolotyrin K.P., Bogatyrev S.A., Savon D.Y., Aleksakhin A.V. Use of resourcesaving technologies in fabrication and restoration of steel bushing-type components via hot plastic deformation. CIS Iron and Steel Review. 2019. No. 2. Pр. 38–41. DOI: 10.17580/cisisr.2019.02.08

8. Rudik F.Ya., Skryabina L.Yu., KovylinA.P., Popova A.V., Volodin V.V. Improvement of wear resistance and fatigue strength of cutting tools of process industry. Vestnik mashinostroeniya = Mechanical Engineering Bulletin 2015. No. 4. Pp. 43–47. (In Russ.)

9. Lisunets N.L. Usage of physical and mathematical simulation for improvement of the process of metal shear cutting. CIS Iron and Steel Review. 2019. Vol. 17. No. 1. Pp. 34–38. DOI: 10.17580/cisisr.2019.01.06

10. Telegin I.V., Volodin I.M. Analysis of the metal consumption of operations parting and heating blanks from rolled bar round section. Fundamental research. 2015. No. 7-4. Pp. 722– 726. (In Russ.)

11. Lisunets N.L., Radyuk A.G., Kolobov A.V., Fedotov E.S., Vinogradov A.I. Simulation of slitting of coiled steel at multidisk shears of coil slitting lines. CIS Iron and Steel Review. 2012. No. 1. Pp. 21–23.

12. Samarina V., Skufina T., Samarin A., Baranov S. Some System Problems of Russian Mining Enterprises of Ferrous Metallurgy. International Review of Management and Marketing. 2016. Vol. 6. No. S1. Pp. 90–94.

13. Shinkevich A.I., Kudryavtseva S.S., Shinkevich M.V., Salimianova I.G., Ishmuradova I.I. Improving the efficiency of production process organization in the resource saving system of petrochemical enterprises. International journal of energy economics and policy. 2019. Vol. 9. No. 4. Pp. 233–239. DOI: 10.32479/ijeep.7966

14. Rudik F.Ya., Scriabina L.Yu., Kovylin P.A., Bulekov T.A., Volodin V.V. Technological features of the boning of the meat raw materials and ways of increasing the durability of the cutting tool. Bulletin of the Saratov State Agrarian University. N.I. Vavilov. 2014. No. 7. Pp. 41–44. (In Russ.)

15. Solovyov S.A., Lyalyakin V.P., Goryachev S.A., Mishina Z.N., Gerasimov V.S., Solovyov R.Yu., Chernoivanov V.I., Golubev I.G. Innovative directions of development of the repair and maintenance base for agricultural machinery. Moscow: Rosinformagrote, 2014. 160 p. (In Russ.)

16. Rudik F.Ya., Skryabina L.Yu., Morgunova N.L. Improving the performance of the knife boning plastic deformation. Saratov: KUBiK, 2016. 120 p. (In Russ.)

17. Tulupov A.S. Economic aspects of voluntary and compulsory environmental insurnce. Economics and Mathematical Methods. 2013. No. 2. Pp. 44–53. (In Russ.)

18. Kuznetsov N.I., Kolotyrin K.P., Dilmanova E.S. Improving environmental performance in the auto recycling system. Management of economic systems. Scientific electronic journal. 2014. No. 8. Pp. 47–53. (In Russ.)

19. Poravny I.M., Kolotyrin K.P., Gengut I.B. The use of environmental insurance in the management of projects to eliminate accumulated environmental damage. Economics of Contemporary Russia. 2017. No. 2. Pp. 78–89. (In Russ.)

20. Cui J., Roven H.J. Recycling of automotive aluminum. Transactions of Nonferrous Metals Society of China. 2010. Vol. 20, No. 11. Pp. 2057– 2063. DOI: 10.1016/S1003-6326(09)60417-9


Review

For citations:


Kolotyrin K.P., Bogatyryov S.A., Rudik F.Ya. Implementation of the new resource saving technology in manufacturing process. Russian Journal of Industrial Economics. 2020;13(4):494-502. (In Russ.) https://doi.org/10.17073/2072-1634-2020-4-494-502

Views: 696


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2072-1633 (Print)
ISSN 2413-662X (Online)